Home >> Services>> Diesel Maintenance Spare Parts

Diesel Maintenance Spare Parts

Part No.	DESCRIPTION
22600515-4	Rotor
2261073	Blower inlet sleeve
21523523	Cap screw, intermediate to terbine casing, 1/2-13x3 soc.h.
21513120	Lock washer, 1/2
2261211-1	Oil seal, turbine end
2261212-1	Oil seal, blower end
21529623	Machine, screw, blower oil seal to casing, no. 10-24x1/2 flh
2261209	Bearing, turbine end
2261208	Bearing, blower end
2261231-1	Retaining ring, turbine end oil seal
2261175-1	Gasket, intermediate to turbine casing
2261053	Turbine casing
1639377	Pipe plug, 2-1/2 IPS, CSK
*22601012-6	Inlet casing and nozzle ring (std.offset and marine)
*22601016-6	Inlet casing and nozzle ring (dual fuel)
*22601037-4	Inlet casing and nozle ring (belows manifold)
*22601013-7	Inlet casing and nozzle ring (std)
*22601042-1	Inlet casing and nozzle ring (single duct manifold)
*22601014-6	Inlet casing and nozzle ring (marine)
*22601036-3	# Inlet casing and nozzle ring (eight duct and dual fuel)
22600417-2	Inlet casing (std offset and manne)
22600416-1	Inlet casing (straight and streamline single duct)
22600414-3	Inlet casing (dual fuel)
2261265-3	Inlet casing (concentric, belows manifold)
22600414-3	Inlet casing (four duct and marine)
2260049-2	# Inlet casing and nozzle ring (eight duct)
22610466-3	Nozzle nng
22610417-4	Nozzle ring (four and eight duct)
22610433-3	Nozzle ring (straight and stream line single duct)
5261073-3	Nozzle ring (marine)
22610602-1	Heat shild
2155891	Bolt, spl. Nozzle ring to casing
2261143-1	Nut, spl. Nozzle ring bolt
*2261597	Tablock Lockplate
2157005	010ckwire,0625 dia. X 12 in. stainless stl.
21526088	Machine screw, inlet casing locating, 3\8-16 x 3\4,f1. H
	stn. Stl.(straight and streamline single duct)
2261551	Connector, inlet casing to manifold (straight single duct)
2261552-2	Connector, inlet casing to manifold (straight single duct only)
21536511	Gasket Connector to inlet casing (straight and streamline single duct)
2261154	Cap screw, inlet to turbine casing (integral flange application)
2261158	Cap screw, clamp ring, inlet to turbine casing, clamp ring
	straight and streamline single duct)
21513199	Lock washer, 5/8, stainless steel
2261373	Clamping ring, inlet to turbine casing
2261461	Clamping ring, inlet to turbine casing (8 duct)
2261,541	Reinforcing ring, connector and inlet casing to turbine
	casing (straight single duct only)
2261114	Line, L.O. to turbo
16394015-1	Tube, 1/20.0. x 049 wall x 21 - 1 14 inch.
1639331	Connector, male, 1/200 x 3/8 IPS
1639462	Reducer, 1/2 IPS x 3/8 IPS
24018357	Clamp, L.O. pipe
21513526-1	Cap screw clamp to turbo, 3/8-16x7/8
2151692-1	Nut, 3/8-16
2151312-1	Lock washer, 3/8
16393912	Bushing, 1 IPS x 3/8 IPS
2261312	Turbo to support bracket (std.)
	Bracket, supplier (marine and stationery) order by D.E. and Engine Srl.No.
2151352-1	Cap screw, braket to turbo, 5/8 - 11 x 1-1/2
2151311-1	Lock washer, 5/8
21555872	Cap screw, braket to spacer, 5/8-11 x 1-3/4
2151691-1	Nut, 5/8 - 11
2151311-1	Lock washer, 5/8
2261353-2	Spacer, turbo to support
22610211	Shim, spacer to support
21555880	Cap screw, spacer to support, 3/4-10 x 2-3/4
2151695-1	Nut, 3/4-10
2151318-1	Lock wahser, 3/4
1441013-1	Gasket, turbo exhaust outlet
AFTER COOLER
Part No.	DESCRIPTION
2280154	After coller with bottom cover
2280156	After coller with bottom cover
2280155	After coller with bottom cover
2280157	After coller with bottom cover
2281881	After coller only
2281882	After coller only
2281654	Cover, bottom
2281657	Cover, bottom
2152489	Gasket, bottom cover to after cooler
21513513	Capscrew, bottom cover to after cooler, 1/2 in.-13
	, 11/2 in., hex.h
2151313	Lockwasher, 1/2 in
*22816511	Cover, top (600 turbo only)
*2281656	Cover top (510 and 710 turbo only)
*2281659	Cover top (510 and 710 turbo only)
2152488	Gasket, cover to after cooler
2281871	Plate, after cooler centering, in turbo support
2281872	Plate, after cooler centering, in turbo support
21524810	Gasket, centering plate to support
21524811	Gasket, entering plate to support
21513510	Capscrew, cetering plate to support, 1/2
2151313	Lockwasher, 1/2 in
2281891	"0" ring, bottom cover
21513571	Capscrew, top cover to after cooler, 3/8 in. -16, 23/4 in. hex h
CAMSHAFT WITH GEAR
Part No.	DESCRIPTION
21600212	Camshaft, main, right side
2161059	Camshaft section, free end, cyls. 1,2
2161065	Camshaft section, intermediate,cyls. 3,4
2161093	Camshaft section, intermediate,cyls. 5,6
*2161077	Camshaft section, gear end, cyls. 7,8
16393715	Pipe plug, geneator end, 1/2 IPS, hex. Soc
2151054	Dowel, straight, section locating, 1/2 dia. X 1 in.
21514280-1	Stud bolt, spl., section fastening
*21513730	Nut, Elastic stop, 1/2-20
2157001	010ckwire, .054 dia. x 12 ft. (not required with stop nut)
21512742	Key, spl. , gear to shaft
21600114	Camshaft, main, left side
2161014	Camshaft section, free end, cyls. 1,2
2161103	Camshaft section, intermediate,cyls. 3,4
2161113	Camshaft section, intermediate,cyls. 5,6
2161034	Camshaft section, gear end, cyls 7,8
16393715	Pipe plug, geneator end, 1/2 IPS, hex. Soc
2151054	Dowel, straight, section locating, 1/2 dia. X 1 in
21514280-1	Stud bolt, spl., section fastening
21513730	Nut, Elastic stop, 1/2-20
2157001	010ckwire, .054 dia. x 12 ft. (not required with stop nut)
21512742	Key, spl. , gear to shaft
2351016	Gear, camshaft, right and left side (Dwg. 35A71069-1)
2155172	Nut,spl. Gear to shaft
2154968	Cap screw, locking nut, 3/8 - 16 x 1-1/4
2157001	Lockwire, .054 dia x 6 inch.
2155621	Ring, snap, internal
2154969	Cap screw, key to gear, 3/8-16 x 2
2157001	Locking wire, .054 dia x 6 inch
*21600218	Main cam shaft, right side
*21610222	Cam shaft section, free end cyls. 1,2
*21610223	Camshaft section, intermedia"te,cyls. 3,4
*21610224	Camshaft section, intermediate,cyls. 5,6
21610225	Camshaft section, gear end, cyls. 7,8
16393715	Pipe plug, geneator end, 1/2 IPS, hex. Soc
2151054	Dowel, straight, section locating, 1/2 dia. X 1 in
*2151682	Stud bolt, spl., section fastening
*21513753	Nut, Elastic stop, 1/2-20
2157001	Lockwire, .054 dia. x 12 ft. (not required with stop nut)
21512742	Key, spl. , gear to shaft
*21600122	Camshaft, main, left side
*21610127	Camshaft section, free end, cyls. 1,2
*21610128	Camshaft section, intermediate,cyls. 3,4
*21610129	Camshaft section, intermediate,cyls. 5,6
*21610130	Camshaft section, gear end, cyls. 7,8
16393715	Pipe plug, geneator end, 1/2 IPS, hex. Soc
2151054	Dowel, straight, section locating, 1/2 dia. X 1 in
*2151682	Studbolt, spl., section fastening
21513753	Nut, Elastic stop, 1/2-20
7157001	Lockwire,054 dia x 12 ft. (not required with stop nut)
21512742	Key, spl. , gear to shaft
*23510114	Cam shaft gear, right side (dwg. 35 A 71110-1) with timing marks
2351016	Cam shaft gear, right or left side (dwg. No.3571069-1) without timing mark
2351018-1	Cam shaft gear, right and left side (dwg NO.35 A -71110-2 and
	dwg. No.35A-72069-2) with timing marks
2155172	Nut, spl. Gear to shaft
2154968	Cap screw, locking nut, 318 - 16 x 1-1/4
2157001	Locking wire, .054 dia x 6 inch.
2155621	Internal snap ring
2154969	Cap screw, key to gear, 3/8-16 x 2
2157001	Lock wire, .054 x 6 inch
21559317	Molykote "Z" powder (10 oz. squeeze tube) applied to all new camshaft
21611714	Cover, camshaft, right side
21611711	Cover, camshaft, gear right or left
1639374	Pipe plug, incover, 1/4 IPS sq.h.
21611716	Cover camshaf gear left side
21611712	Cover, camshaft gear, right side
21522627	Gasket, camshaft gear cover to block
21513510	Capscrew, cover to block, 1/2 in - 13, 11/4 in, hexh
21513554	Capscrew, cover to block, 1/2 In -31/2 in. hexh
2151318	Lockwasher, 112 in
2151775	Dowel, taper, cover to block, no.9, 11/2 inch
1639376	Pipe plug, incover, 1 in., IPS sq.h
21611722	Cover, 4 gear cover at tach. Gen. drive opening
21522616	Gasket, cover to gear cover
21513541	Capscrew, cover to gear cover 3/8-16, 1, hex h.
2151312	Lockwasher, 3/8
21522616-1	Gasket, bearing housing to camshaft gear cover
21555893	Capscrew, bearing housing to camshaft gear cover, 3/8-16x1
2151312	Lockwasher, 3/8
21600214	Main camshaft, right side
21610514	Camshaft section, free end, cyls 1-2
21610212	Camshaft section, intermediate, cyls. 3-4
21610317	Camshaft section intermediate cyls. 5-6
21610711	Camshaft section, gear end, cyls. 7-8
16393715	Pipe plug, generator end, 1/2 IPS, Hex soc
2151054	Dowel, straight, section locating, 1/2 x 1
21514280-1	Stud bolt, spl., section fastening
21513730	Nut, Elastic stop, 1/2-20
21512742	key, spl. Gear to shaft
21600116	Main camshaft, left side
21610117	Camshaft section, free end, cyls. 1-2
2161104	Camshaft section, intermediate, cyls. 3-4
2161114	Camshaft section intermediate cyls. 5-6
21610710	Camshaft section, gear end, cyls. 7-8
16393715	Pipe plug, generator end 1/2 IPS, Hex soc
2151054	Dowel, straight, section locating, 1/2 x 1
21514280-1	Stud bolt, spl., section fastening
21513730	Nut, Elastic stop, 1/2-20
21512742	key, spl. Gear to shaft
23510112	Camshaft gear, right and left side (Dwg. No.3571069-4 or 35A7111 0-4)
2155172	Nut, supplier, gear to shaft
2154968	Cap screw, locking nut, 3/8-16x1-1/4
2157001	Lockwire, 054x6 inch
2155621	Internal snap ring
2154969	Cap screw, key to gear 3/8-16x2
2157001	Lockwire, 054x6 inch
21559317	Molykote "Z" Powder (10 oz. squeeze tube) apply to ail new camshaft
21600214	Main camshaft,right side
21610514	Camshaft section, free end, cyls. 1-2
21610212	Camshaft section, intermediate, cyls. 3-4
21610317	Camshaft section intermediate cyls 5-6
21610711	Camshaft section, gear end, cyls 7-8
16393715	Pipe plug, generator end, 1/2 IPS, Hex soc
2151054	Dowel, straight, section locating, 1/2 x 1
21514280-1	Stud bolt, spl., section fastening
*21513730	Nut, Elastic stop, 1/2-20
2157001	Lockwire, 054x12 ft (not required with stop nut)
21512742	key, spl. Gear to shaft
21600116	Main camshaft, left side
21610117	Camshaft section, free end, cyls. 1-2
2161104	Camshaft section, intermediate, cyls. 3-4
2161114	Camshaft section intermediate cyls. 5-6
21610710	Camshaft section, gear end, cyls. 7-8
16393715	Pipe plug, generator end, 1/2 IPS, Hex soc
2151054	Dowel, straight, section locating, 1/2 x 1
21514280-1	Stud bolt, spl., section fastening
21513730	Nut. Elastic stop, 1/2-20
2157001	Lockwire, 054x12 ft (not required with stop nut)
21512742	key, spl. Gear to shaft
23510110	Gear, camshaft, right and left side (Dwg. No.3571069-2)
	215-C or E Engine
2351016	Cam shaft gear, right or left side (dwg. No.3571069-1) 251-B Engine
*2351018-1	Cam shaft gear, right and left side (dwg. No.35 A -71110-2)
2155172	Nut, spl. Gear to shaft
2154968	Cap screw, locking nut, 3/8 - 16 x 1-1/4
2157001	Locking wire, .054 dia x 6 inch
2155621	Internal snap ring
2154969	Cap screw, key to gear, 3/8-16 x 2
2157001	Lock wire, .054 x 6 inch
21559317	Molykote "Z" powder (10 oz. squeeze tube) applied to all new camshaft
21600212	Camshaft, main, right side
2161059	Camshaft section, free end, cyls. 1,2
2161065	Camshaft section, intermediate,cyls. 3,4
2161093	Camshaft section, intermediate,cyls. 5,6
2161077	Camshaft section, gear end, cyls. 7,8
16393715	Pipe plug, geneator end, 1/2 IPS, hex. Soc
2151054	Dowel, straight, section locating, 1/2 dia X 1 in.
21514280-1	Studbolt, spl., section fastening
*21513730	Nut, Elastic stop, 1/2-20
2157001	Lockwire, .054 dia. x 12 ft. (not required with stop nut)
21512742	Key, spl. , gear to shaft
21600114	Camshaft, main, left side
2161014	Camshaft section, free end, cyls. 1,2
2161103	Camshaft section, intermediate,cyls. 3,4
2161113	Camshaft section, intermediate,cyls. 5,6
2161034	Camshaft section, gear end, cyls. 7,8
16393715	Pipe plug, geneator end, 1/2 IPS, hex Soc
2151054	Dowel, straight, section locating, 1/2 dia. X 1 in.
21514280-1	Studbolt, spl., section fastening
21513730	Nut, Elastic stop, 1/2-20
2157001	Lockwire, .054 dia. x 12 ft. (not required with stop nut)
21512742	Key, spl. , gear to shaft
2351016	Gear, camshaft, right and left side (Dwg. 35A71 069-1)
2155172	Nut,SPI. Gear to shaft
2154968	Cap screw, locking nut, 3 /8 - 16 x 1-1/4
2157001	Lockwire, .054 dia x 6 inch
2155621	Ring, snap, internal
2154969	Cap screw, key to gear, 3/8-16 x 2
2157001	Locking wire, .054 dia x 6 inch
22610602-1	Heat shild
2155891	Bolt, spl. Nozzle ring to casing
2261143-1	Nut, spl. Nozzle ring bolt
*2261597	T ablock Lockplate
2157005	0lockwire, .0625 dia. X 12 in. stainless stl
21526088	Machine screw, inlet casing locating, 3\8-16 x 3\4,fl. H
	stn. Stl.(straight and streamline single duct)
2261551	Connector, inlet casing to manifold (straight single duct)
2261552-2	Connector, inlet casing to manifold (straight single duct only)
21536511	Gasket Connector to inlet casing (straight and streamline single duct)
2261154	Cap screw, inlet to turbine casing (integral flange application)
2261158	Cap screw, clamp ring, inlet to turbine casing, clamp ring
	straight and streamline single duct)
21513199	Lock washer, 5/8, stainless steel
2261373	Clamping ring, inlet to turbine casing
2261461	Clamping ring, inlet to turbine casing (8 duct)
2261541	Reinforcing ring, connector and inlet casing to turbine
2261114	casing (straight single duct only)
16394015 1	Line, L.O. to turbo
1639331	Tube, 1/20 D x 049 wall x 21 1 /4 inch
1639462	Connector, male, 1/2 OD x 3/8 IPS
24018357	Reducer, 1/2 IPS x 3/8 IPS
21513526-1	Clamp, L.O. pipe
2151692-1	Cap screw clamp to turbo, 3/8-16x7/8
2151312-1	Nut, 3/8-16
16393912	Lock washer, 3/8
2261312	Bushing, 1 IPS x 3/8 IPS
2151352-1	Turbo to support bracket (std.)
2151311-1	Bracket, supplier (marine and stationery) order by DE. and Engine Srl.No
21555872	Cap screw, braket to turbo, 5/8 - 11 x 1-1/2
2151691-1	Lock washer, 5/8
2151311-1	Cap screw, braket to spacer, 5/8-11 x 1-3/4 Nut, 5/8 - 11
2261353-2	Lock washer, 5/8
22610711	Spacer, turbo to support
21555880	Shim, spacer to support
2151695-1	Cap screw, spacer to support, 3/4-10 x 2-3/4 Nut, 3/4-10
2151318-1	Lock wahser, 3/4
1441013-1	Gasket, turbo exhaust outlet
Contact us for Query / More Details